I was a little worried because there was just a bit more… slop? in the fitting between this and the Male QD, but the flex at the joint did not translate to any leakage at all and this made by 3 pc FPT ball valve super mobile. I’ve only brewed using it once but I’m happy with it so far.

I converted my homebrew setup to make all transfer hose connections between HLT, kettle, pumps, mash tun, RIMS tube, etc. quick disconnect rather than barbed fittings. Much faster. These fittings (and similar tri-clamp versions) make everying quick and easy. These are very good quality.

Unless you have existing QD connections, this piece will not suffice on its own. You need the male piece to connect to. This is a quality product that make brew day easier.

Adding QDs can be expensive, but in the long run it is definitely worth it. These QDs are manufactured very well. I have purchased from other stores, but the quality is not the same. The whole unit feels solid and clean.

Does the job very effectively!!

What can you say about a plumbing fitting? It fits, it doesn't leak, it has an o-ring in it that is probably replaceable if it ever wears out.

I use these Male and Female QDs throughout my brewery - Female on all the hoses, and Male on kettles, pumps, heat exchanger, and wort chiller. No leakage whatsoever. They're expensive, but a joy to use.

All stainless Quick Disconnects I've purchased from MoreBeer have worked flawlessly. No leaks and easy clean up. Excellent "must have" equipment for all brewing!

I build up my brewery different every time because I am always moving from apartment to apartment. These quick connects give me the flexibility i need!

Don't go another day without switching to these quick connects!

I have about 10 of these in use, overall a excellent product. Make sure you clean after use well to avoid sticking. One trick I have found that works is to use a spray bottle with San Star and give the inner ring a quick spray before connection, works well! I love the stainless and I expect them to last a long time for sure.

These are threaded on all my kettles, mash-tun, pumps and chiller(s). I have several silicone hoses of various lengths with barbed/male fittings on either end and simply jack the hoses into these receptacles to quickly configure what I'm after - they're fantastic!

So much easier to use then pushing and pulling the hoses off of barbs. A++++ Love them

I found a stainless quick disconnect that looked exactly like this one on another site for $12. That purchase turned into a $12 lesson in quality; the similarity was skin deep and the other unit was junk. The collar squeaked and creaked like the springs were re-purposed from discarded ballpoint pens, it was exceptionally difficult to connect to its male counterpart (which isn't fun when the male counterpart is on a hot brew kettle), and the o-ring buckled and came loose after the first use. Save yourself the trouble and aggravation - spend the extra $3 here for a top-quality product.

Want to upgrade you Brew system and make life easy? Thats what we did when we practically replaced ever hose connections with a Quick disconnect. They feel great going on and off, and it make things very interchangeable for cleaning purposes, and quick installation and removal too. A must have for any Good looking Brew System.

My neighbors and friends (even those that don't homebrew) rave about my quick disconnects. Very easy to use--one hand is all that is needed.

It is much easier to transfer liquids between brew vessels when you use quick disconnects and the stainless ones are very simple to keep sanitary. These are helpful with whatever technique you use from SIMS to HERMS.

Super easy to use and really enhances brew day. I generally clean these by soaking them in boiling water after brew day to get any residual sugars off.

Makes connecting to the pump a piece of cake.

After using CPC connectors for years I was happy to see these come out from More Beer. They will not break like their plastic counterparts and do not leak at all. I changed out all the plastic fittings on my 20 gallon system to use these connectors and been using them now for about three years. Yes they are pricey but these are the last connectors you will have to buy. I suggest you pick up some extra 0-rings just in case one has to be replaced. I have only had to replace one since I have had them.

This was perfect for my tubing/pump/chiller setup.

When brewing 20 gallons batches, you need to pump.These make it effortless. Expensive investment, but you will only need to buy them once.

I got a couple sets of these for my kettles and hoses. Going to get another set for my new 15 gallon kettle.

These mate well with QD and the machining is great. Smooth connecting to male and threads are clean and smooth. I have been purchasing one with each order until I have enough.

High quality stainless steel QD. Works easily and flawlessly. Easy to to clean as well.

I was reluctant to buy QDs for a long time since it is a fairly expensive upgrade to switch out all my hardware. I finally committed to it one day and am glad I did. It saves time and prevents messes. These are pretty heavy duty as well so I feel very comfortable using them and that they will last for a long time.

These are bloody expensive parts but the quality and the functionality is great. The one thing I would warn people is that the rubber washer inside easily comes out. When this washer goes missing the part is useless. You can get a replacement part.

Upgraded from the Kent plastic connector to this style, these have better flow. Better finish and easier to connect than steel camlocks. I'll be ordering more.

A great addition to your brew equipment and well worth the small investment. Makes transfers easy. You'll find you'll want more than just one.

I purchased this to install on my new 10 gal brew system. Upgrading from plastic and brass is always a good ideal for long-term use and better results. I would recommend this product for your system.

These QD's are great! They simplify your brew day and make it more efficient through one hand operation for all on/off kettles, pumps and chillers or whatever. No more fussing with hose clamps and tools to attach and detach hoses. Definitely worth the investment. Time Saver!!!!